Request a quote
HomePainting

Plastic parts painting, next to the press

In-house painting and finishing alongside our moulding shop, for end-to-end manufacturing on one site. Our three-booth paint shop in Chakan is operational and accepting orders for painting-only and moulded-and-painted parts.

Send a painting enquiry See the paint line
3 boothsPrimer, basecoat, clearcoat
PU, acrylic, epoxyPaint systems
800 × 450 × 400 mmPaint envelope, H × W × D
25,000 sq ftPaint shop

The press and the paint booth, under one roof

Our paint shop sits in the same building as our 15 moulding machines. A moulded part reaches the paint line without being packed, trucked or handed to another company.

Moulding shop at the Bhamboli plantMoulding shop

15 presses, 200T–1700T

Parts moulded and checked in our moulding lab.

Overhead conveyorised paint line with part hangersPaint shop

Overhead conveyorised line

Prepared, painted, cured and inspected on site.

Moulding-only and painting-only work is welcome too. We paint parts moulded by other suppliers.

What one supplier for moulding and painting changes

Painted plastic parts often travel between a moulder and a separate painter. Bringing both under one roof removes the hand-off.

Fewer vendors to coordinate

One PO and one contact for moulding, painting and inspection, with one team answerable for the finished part.

No transit between suppliers

Unpainted parts move inside our plant, so there is less handling, packing and transit damage before the first coat.

Defects traced to the source

When a paint defect starts in the substrate, we trace it back to our own moulding process and correct it there.

One production plan

Moulding and paint batches are scheduled together, against your delivery plan.

Paint-ready materials

Paintable-grade PC ABS is already part of our material mix, so material and finish are planned together.

Inspection on both sides

Parts are checked in our moulding lab before painting and in our paint shop lab before dispatch.

Paint shop with temperature-controlled booths and air supply ducting Overhead paint conveyor with part hangers Paint shop floor with marked zones

Inside the paint shop

A new line built for automotive plastic parts, with each stage separated and controlled.

  • Overhead conveyorised painting plant

    Parts hang on an overhead conveyor and travel through preparation, the booths and the oven without being handled between stages.

  • Dust-control arrangements

    Dust control across the paint area protects the finish on visible parts.

  • Isolated loading and unloading zones

    Parts are loaded and unloaded away from the spray area.

  • Pre- and post-painting areas

    Dedicated areas for surface preparation before painting, and for inspection and finishing after.

  • Temperature-controlled PUF-panel booths

    Three booths for primer, basecoat and clearcoat. Single-coat systems are also possible.

  • Temperature-controlled air supply

    A dedicated air supply unit feeds the booths.

  • Conveyorised gas-fired oven

    Controlled-temperature curing, typically 80 °C for 30 minutes.

  • Variable conveyor speed

    Line speed is adjusted to the part and the paint system.

  • Dedicated paint kitchen

    Shades are prepared and matched in-house, to customer requirement.

What we can paint

Plastic parts up to H 800 × W 450 × D 400 mm, in the paint system and finish your drawing calls for. Send the drawing if your part is close to the limit and we’ll confirm.

PUAcrylicEpoxyPrimerBasecoatClearcoatSingle-coat
Glossy
Semi-glossy
Matt
H 800 W 450 D 400

Painting process flow

Twelve stages, from pre-inspection to post-inspection.

01Pre-inspection
02Loading
03IPA and tack-rag cleaning
04Anti-static air blow
05Primer application
06Flash off6–8 min
07Basecoat application
08Flash off5–7 min
09Clearcoat application
10Flash off8–10 min
11Baking80 °C / 30 min
12Post-inspection

Pre-treatment

Manual IPA wipe, tack-rag, de-ionisation and manual flaming.

Post-paint operations

Buffing, polishing and a dedicated touch-up booth.

Environment and safety

PUF-panel booths, dedicated air supply unit, paint sludge handling, sprinklers and fire-fighting systems.

Paint shop quality lab

DFT, wet film thickness, cross-cut adhesion, pencil hardness, Ford cup viscosity and Hegman gauge. See our labs

Need plastic parts painted?

Painting-only, or moulded and painted. Share the drawing, paint system and finish, and we’ll confirm fit with our paint envelope.

Send a painting enquiry
Chandrakant ManeDirector +91 99756 80902 mane.c@creenos.in
Shantanu BhujbalDirector +91 96040 39155 marketing@creenos.in
Creenos Polymers Pvt. Ltd., Gat No. 43/3, 1H20R, Bhamboli, MIDC, Chakan, Pune – 410507